CubieBoard中文论坛

 找回密码
 立即注册
搜索
热搜: unable
查看: 5971|回复: 2

cubieboard2 启动日志 can't open '/system/bin/ethtool' 这个是什么错误

[复制链接]
发表于 2018-1-15 00:34:25 | 显示全部楼层 |阅读模式
cubieboard2 启动日志  can't open '/system/bin/ethtool' 这个是什么错误

用usb-ttl登陆

=======================================

init: no such service 'ric'
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =1024
card boot number = 2
card no is 2
sdcard 2 line count 0
[mmc]: SD/MMC Card: 4bit, capacity: 3700MB
[mmc]: vendor: Man 0x00880804 Snr 0x3800321f
[mmc]: product: NCard
[mmc]: revision: 3.2
sdcard 2 init ok
The size of uboot is 0x000a4000.
sum=0x2d56469e
src_sum=0x2d56469e
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[      0.159]

U-Boot 2011.09-rc1-00003-ge89ab14-dirty (Jan 03 2014 - 12:57:33) Allwinner Technology

[      0.169]version: 1.1.0
[      0.172]pmbus:   ready
[      0.276]PMU: AXP209
[      0.279]PMU: AXP20x found
[      0.282]PMU: bat ratio = 100
[      0.286]after set, dcdc2 =1450mv
[      0.289]PMU: dcdc2 1450
[      0.292]PMU: pll1 912 Mhz
boot_clock = 912
dcdc2_vol = 1450
[      0.300]after set, dcdc2 =1450mv
dcdc3_vol = 1300
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 1
storage_type = -1
usb_recovery = 1
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      0.336]DRAM:  1 GiB
relocation Offset is: 35b23000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
DRV_DISP_Init: opened
[      0.549]boot_disp.output_type=3
[      0.553]boot_disp.output_mode=5
[      0.556]boot_disp.auto_hpd=1
workmode = 0
MMC:         2
SUNXI SD/MMC: 2
Man 880804 Snr 3800321f
NCard
3.2
---------------MMC version 4.0---------------
---------------mmc->clock 50000000-----------
---------------mmc->bus_width 4--------------
boot0 capacity: 0KB,boot1 capacity: 0KB
[      1.899]sunxi flash init ok
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:11-
-name-        -start-       -size-      
bootloader  : 1000000       2000000     
env         : 3000000       1000000     
boot        : 4000000       1000000     
system      : 5000000       20000000   
recovery    : 25000000      2000000     
databk      : 27000000      10000000   
misc        : 37000000      1000000     
private     : 38000000      1000000     
data        : 39000000      40000000   
cache       : 79000000      14000000   
UDISK       : 8d000000      0           
-----------------------------------
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
recovery key high 6, low 4
cant find fstbt value
to be run cmd=run setargs_mmc boot_normal
the user data'magic is bad
WORK_MODE_BOOT
sunxi_bmp_display
WORK_MODE_BOOT
[      2.001]Hit any key to stop autoboot:  0
read boot or recovery all
[      2.575]sunxi flash read ffset 4000000, 12332351 bytes OK
[      2.583]ready to boot
[      2.586]
Starting kernel ...

aw_pm_init: not support super standby.
can't get item for emac_power gpio !
[hdmi]hdmi module init
##fb init:w=1280,h=720,fbmode=3
init: reading config file
init: /init.rc: 638: invalid option 'chmod'
init: /init.rc: 639: invalid option 'chown'
init: -----------没找到sata节点,nand启动--------------
init: /init.sun7i.rc: 174: ignored duplicate definition of service 'ril-daemon'
init: start e2fsck listening...
[hdmi]hdmi module init
init: do_umount: /data
init: do_umount: /cache
init: dont need format /dev/block/UDISK
init: dont need format /dev/block/private
init: do_umount: /databk
failed to get gpio_para used information
[sunxi_leds_init] request gpio188 failed
ft5x_ts: module is already loaded
videobuf_core: exports duplicate symbol __videobuf_mmap_setup (owned by kernel)
init: [william] tvstatus = 0!
init: HDMI status = 0, try 40 times!TV status = 0
videobuf_dma_contig: exports duplicate symbol videobuf_dma_contig_free (owned by kernel)
init: untracked pid 1166 exited
init: C_IN_START
android_usb: already disabled
init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead
init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead
sh: can't open '/system/bin/ethtool'init: path = /dev/block/data

init: C_IN_START
init: path = /dev/block/cache
init: no such service 'ric'
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =1024
HELLO! BOOT0 is starting!
boot0 version : 3.0.0
dram size =1024
card boot number = 2
card no is 2
sdcard 2 line count 0
[mmc]: SD/MMC Card: 4bit, capacity: 3700MB
[mmc]: vendor: Man 0x00880804 Snr 0x3800321f
[mmc]: product: NCard
[mmc]: revision: 3.2
sdcard 2 init ok
The size of uboot is 0x000a4000.
sum=0x2d56469e
src_sum=0x2d56469e
Succeed in loading uboot from sdmmc flash.
Ready to disable icache.
Jump to secend Boot.
[      0.159]

U-Boot 2011.09-rc1-00003-ge89ab14-dirty (Jan 03 2014 - 12:57:33) Allwinner Technology

[      0.169]version: 1.1.0
[      0.172]pmbus:   ready
[      0.276]PMU: AXP209
[      0.279]PMU: AXP20x found
[      0.282]PMU: bat ratio = 100
[      0.286]after set, dcdc2 =1450mv
[      0.289]PMU: dcdc2 1450
[      0.292]PMU: pll1 912 Mhz
boot_clock = 912
dcdc2_vol = 1450
[      0.300]after set, dcdc2 =1450mv
dcdc3_vol = 1300
ldo2_vol = 3000
ldo3_vol = 2800
ldo4_vol = 2800
power_start = 1
storage_type = -1
usb_recovery = 1
find power_sply to end
fel key old mode
run key detect
no key found
no key input
dram_para_set start
dram_para_set end
[      0.336]DRAM:  1 GiB
relocation Offset is: 35b23000
donn't initialize ther user_gpio (main_key:boot_init_gpio)
DRV_DISP_Init: opened
[      0.549]boot_disp.output_type=3
[      0.553]boot_disp.output_mode=5
[      0.556]boot_disp.auto_hpd=1
workmode = 0
MMC:         2
SUNXI SD/MMC: 2
Man 880804 Snr 3800321f
NCard
3.2
---------------MMC version 4.0---------------
---------------mmc->clock 50000000-----------
---------------mmc->bus_width 4--------------
boot0 capacity: 0KB,boot1 capacity: 0KB
[      1.899]sunxi flash init ok
In:    serial
Out:   serial
Err:   serial
--------fastboot partitions--------
-total partitions:11-
-name-        -start-       -size-      
bootloader  : 1000000       2000000     
env         : 3000000       1000000     
boot        : 4000000       1000000     
system      : 5000000       20000000   
recovery    : 25000000      2000000     
databk      : 27000000      10000000   
misc        : 37000000      1000000     
private     : 38000000      1000000     
data        : 39000000      40000000   
cache       : 79000000      14000000   
UDISK       : 8d000000      0           
-----------------------------------
base bootcmd=run setargs_mmc boot_normal
bootcmd set setargs_mmc
key 0
recovery key high 6, low 4
cant find fstbt value
to be run cmd=run setargs_mmc boot_normal
the user data'magic is bad
WORK_MODE_BOOT
sunxi_bmp_display
WORK_MODE_BOOT
[      2.001]Hit any key to stop autoboot:  0
read boot or recovery all
[      2.575]sunxi flash read ffset 4000000, 12332351 bytes OK
[      2.583]ready to boot
[      2.586]
Starting kernel ...

aw_pm_init: not support super standby.
can't get item for emac_power gpio !
[hdmi]hdmi module init
##fb init:w=1280,h=720,fbmode=3
init: reading config file
init: /init.rc: 638: invalid option 'chmod'
init: /init.rc: 639: invalid option 'chown'
init: -----------没找到sata节点,nand启动--------------[mmc-err] smc 2 err, cmd 52,  RTO
init: /init.sun7i.rc: 174: ignored duplicate definition of service 'ril-daemon'
init: start e2fsck listening...
[hdmi]hdmi module init
init: do_umount: /data
init: do_umount: /cache
init: dont need format /dev/block/UDISK
init: dont need format /dev/block/private
init: do_umount: /databk
failed to get gpio_para used information
[sunxi_leds_init] request gpio188 failed
ft5x_ts: module is already loaded
videobuf_core: exports duplicate symbol __videobuf_mmap_setup (owned by kernel)
videobuf_dma_contig: exports duplicate symbol videobuf_dma_contig_free (owned by kernel)
init: [william] tvstatus = 0!
init: HDMI status = 0, try 40 times!TV status = 0
init: untracked pid 1166 exited
android_usb: already disabled
sh: can't open '/system/bin/ethtool'init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead

init: using deprecated syntax for specifying property 'sys.usb.config', use ${name} instead
init: C_IN_START
init: path = /dev/block/data
init: C_IN_START
init: path = /dev/block/cache
init: no such service 'ric'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
init: untracked pid 2574 exited
init: sys_prop: permission denied uid:1003  name:service.bootanim.exit
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'
init: untracked pid 3190 exited
sh: can't open '/system/bin/ethtool'
sh: can't open '/system/bin/ethtool'



回复

使用道具 举报

 楼主| 发表于 2018-1-17 00:21:51 | 显示全部楼层

回复 支持 反对

使用道具 举报

 楼主| 发表于 2018-1-19 18:27:38 | 显示全部楼层
重新刷了系统好了
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

QQ|Archiver|手机版|粤ICP备13051116号|cubie.cc---深刻的嵌入式技术讨论社区

GMT+8, 2024-3-29 09:47 , Processed in 0.022892 second(s), 15 queries .

Powered by Discuz! X3.4

© 2001-2012 Comsenz Inc. | Style by Coxxs

返回顶部