Cubieboard安装Openwrt教程 (可以不需要编译)
本帖最后由 tll 于 2013-6-21 23:47 编辑感谢hipboi，本帖子在Ubuntu 12.04.1 （Mac）下写
A 直接用img弄，但是这样分区大小固定
img我用的是512的卡导出的，下次给
B 用fdisk分区，分区大小为最大
其中分两个，一种不编译，下载编译好的，一种自己编译
这里讲不需要编译的
先下载东西：wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/openwrt-sunxi-cubie-rootfs.tar.gz
#下载rootfs
wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/script.bin
#下载script.bin配置文件
wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/sunxi-spl.bin
wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/u-boot.bin
#下载uboot
wget http://stud.netgroup.uniroma2.it/~saverio/sunxi/v4/openwrt-sunxi-uImage
#下载uimage
然后呢，插入SD卡（读卡器），使用dmesg命令看下SD卡是哪个文件，我就因为弄错文件而把我的本地磁盘格式化了……幸亏找回了数据
我这里以/dev/sdb为例开始
Ubuntu会自动挂上插入的磁盘，所以我们需要去掉挂载（假设我的SD上有两个分区）umount /dev/sdb1
umount /dev/sdb2然后开始分区咯，先用fdisk -l记录下磁盘的数据（这是我另一个卡，只有32M，给大家做演示的）Disk /dev/sdb: 32 MB, 32112640 bytes
2 heads, 32 sectors/track, 980 cylinders, total 62720 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x00000000
Device Boot Start End Blocks IdSystem
由上可知，1 sector是512字节，即2 sectors就是1kb了，总共有62740个（不同卡可能不同）
再输入 fdisk /dev/sdb，然后输入d 1，再输入 d 2，删除分区（这个不太确定命令是否正确）。
然后开始做第一个分区
要做第一个分区，我们可以使用berryboot的img文件，将他导入进卡即可，这里先不讲。
又或者，你可以继续用fdisk来执行操作，输入n，然后分区号，开始的值都是默认，下面的最后一个sector，我第一个分区需要32M，则
2（2sectors=1k）*1024（1024k=1m）*32（32M）+2048（加上开始的部分）=67584，比我的总数还大，这是因为32M的卡本身就没32M
然后再使用n命令一次，这次全部用默认值，最后用w命令写入。
格式化：mkfs.vfat /dev/sdb1
mkfs.ext4 /dev/sdb2然后呢，新建文件夹/tempmkdir /temp挂上1到/temp，复制文件，去掉，又上2，解压rootfsmount /dev/sdb1 /temp
cp openwrt-sunxi-uImage /mnt/temp/uImage
cp script.bin /mnt/temp/
umount /mnt/temp
mount /dev/sdb2 /temp
cp openwrt-sunxi-cubie-rootfs.tar.gz /tmp
cd /mnt/temp
<pre>tar -zxvf /tmp/openwrt-sunxi-cubie-rootfs.tar.gz
cd
umount /mnt/temp
</pre>
OK~
该写入uboot了，执行：dd if=sunxi-spl.bin of=/dev/sdb bs=1024 seek=8
dd if=u-boot.bin of=/dev/sdb bs=1024 seek=32接下来插上TTL，然后给cb放上SD卡（两个都是必需要做），在终端里安装screen：apt-get install screen -y接着启动： screen /dev/ttyUSB0 115200此时终端变空了，插上电源，在3秒倒数是按下任意按钮进入uboot命令行，输入：setenv setargs setenv bootargs console=${console} root=${root} loglevel=${loglevel} ${panicarg} ${extraargs} init=/etc/preinit
saveenv
原因：openwrt要先启动preinit而不是直接启动init
好了，使用boot命令启动吧~
最后附上启动出现的字：U-Boot SPL 2012.10-04280-g1a8ac55 (May 25 2013 - 19:42:12)
DRAM: 1024MB
SUNXI SD/MMC: 0
U-Boot 2012.10-04280-g1a8ac55 (May 25 2013 - 19:42:12) Allwinner Technology
CPU: SUNXI Family
Board: Cubieboard
I2C: ready
DRAM:1 GiB
MMC: SUNXI SD/MMC: 0
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot:0
reading uEnv.txt
** Unable to read "uEnv.txt" from mmc 0:1 **
Loading file "uEnv.txt" from mmc device 0:1
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - mmc 0:1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]>
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
Loading file "boot/uEnv.txt" from mmc device 0:1
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - mmc 0:1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]>
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
reading boot.scr
** Unable to read "boot.scr" from mmc 0:1 **
Loading file "boot.scr" from mmc device 0:1
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - mmc 0:1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]>
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
Loading file "boot/boot.scr" from mmc device 0:1
Failed to mount ext2 filesystem...
** Bad ext2 partition or disk - mmc 0:1 **
ext2load - load binary file from a Ext2 filesystem
Usage:
ext2load <interface> <dev[:part]>
- load binary file 'filename' from 'dev' on 'interface'
to address 'addr' from ext2 filesystem
reading script.bin
43628 bytes read
reading uImage
3410200 bytes read
## Booting kernel from Legacy Image at 48000000 ...
Image Name: Linux-3.4.43
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3410136 Bytes = 3.3 MiB
Load Address: 40008000
Entry Point:40008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0
[ 0.000000] Linux version 3.4.43 (saverio@nockid) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2012.12 r36556) ) #1 PREEMPT Sat May 25 19:11:24 CEST 2013
[ 0.000000] CPU: ARMv7 Processor revision 2 (ARMv7), cr=10c5387d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: sun4i
[ 0.000000] Memory Reserved:
[ 0.000000] SYS: 0x43000000 - 0x4300ffff(64 kB)
[ 0.000000] VE : 0x44000000 - 0x48ffffff(80 MB)
[ 0.000000] G2D: 0x49000000 - 0x49ffffff(16 MB)
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] chip-id: A10 (AW1623 revision C)
[ 0.000000] On node 0 totalpages: 262144
[ 0.000000] free_area_init_node: node 0, pgdat c0669974, node_mem_map c0710000
[ 0.000000] Normal zone: 1520 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 193040 pages, LIFO batch:31
[ 0.000000] HighMem zone: 528 pages used for memmap
[ 0.000000] HighMem zone: 67056 pages, LIFO batch:15
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.Total pages: 260096
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/mmcblk0p2 rootwait loglevel=8 panic=10 init=/etc/preinit
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Memory: 1024MB = 1024MB total
[ 0.000000] Memory: 933936k/933936k available, 114640k reserved, 270336K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector: 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap: 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xf0000000 - 0xff000000 ( 240 MB)
[ 0.000000] lowmem: 0xc0000000 - 0xef800000 ( 760 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 (14 MB)
[ 0.000000] .text : 0xc0008000 - 0xc0600000 (6112 kB)
[ 0.000000] .init : 0xc0600000 - 0xc062a000 ( 168 kB)
[ 0.000000] .data : 0xc062a000 - 0xc0672d98 ( 292 kB)
[ 0.000000] .bss : 0xc0672dbc - 0xc070f220 ( 626 kB)
[ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:128
[ 0.000000] timer0: Periodic Mode
[ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 4294967286ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 383.38 BogoMIPS (lpj=1916928)
[ 0.050000] pid_max: default: 32768 minimum: 301
[ 0.050000] Mount-cache hash table entries: 512
[ 0.050000] CPU: Testing write buffer coherency: ok
[ 0.050000] Setting up static identity map for 0x4044dc10 - 0x4044dc68
[ 0.050000] devtmpfs: initialized
[ 0.050000] dummy:
[ 0.050000] NET: Registered protocol family 16
[ 0.050000] Init eGon pin module V2.0
[ 0.050000] SOFTWINNER DMA Driver, (c) 2003-2004,2006 Simtec Electronics
[ 0.050000] Initialize DMAC OK
[ 0.050000] bio: create slab <bio-0> at 0
[ 0.050000] SCSI subsystem initialized
[ 0.050000] libata version 3.00 loaded.
[ 0.050000] usbcore: registered new interface driver usbfs
[ 0.050000] usbcore: registered new interface driver hub
[ 0.050000] usbcore: registered new device driver usb
[ 0.050000] Linux video capture interface: v2.00
[ 0.050000] Advanced Linux Sound Architecture Driver Version 1.0.25.
[ 0.050000] Bluetooth: Core ver 2.16
[ 0.060000] NET: Registered protocol family 31
[ 0.060000] Bluetooth: HCI device and connection manager initialized
[ 0.060000] Bluetooth: HCI socket layer initialized
[ 0.060000] Bluetooth: L2CAP socket layer initialized
[ 0.060000] Bluetooth: SCO socket layer initialized
[ 0.060000] cfg80211: Calling CRDA to update world regulatory domain
[ 0.060000] Switching to clocksource aw 64bits couter
[ 0.060000] FS-Cache: Loaded
[ 0.060000] CacheFiles: Loaded
[ 0.090000] sw_hcd_host0 sw_hcd_host0: sw_hcd host driver
[ 0.090000] sw_hcd_host0 sw_hcd_host0: new USB bus registered, assigned bus number 1
[ 0.090000] hub 1-0:1.0: USB hub found
[ 0.090000] hub 1-0:1.0: 1 port detected
[ 0.090000] NET: Registered protocol family 2
[ 0.090000] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.090000] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.100000] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.100000] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.100000] TCP: reno registered
[ 0.100000] UDP hash table entries: 512 (order: 1, 8192 bytes)
[ 0.100000] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[ 0.100000] NET: Registered protocol family 1
[ 0.100000] audit: initializing netlink socket (disabled)
[ 0.100000] type=2000 audit(0.099:1): initialized
[ 0.100000] highmem bounce pool size: 64 pages
[ 0.110000] VFS: Disk quotas dquot_6.5.2
[ 0.110000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.120000] fuse init (API version 7.18)
[ 0.120000] msgmni has been set to 1296
[ 0.120000] alg: No test for stdrng (krng)
[ 0.120000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.120000] io scheduler noop registered
[ 0.120000] io scheduler deadline registered
[ 0.120000] io scheduler cfq registered (default)
[ 0.120000] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.130000] : used uart info.: 0x05
[ 0.130000] : serial probe 0 irq 1 mapbase 0x01c28000
[ 0.150000] sunxi-uart.0: ttyS0 at MMIO 0x1c28000 (irq = 1) is a U6_16550A
[ 0.680000] console enabled
[ 0.680000] : serial probe 2 irq 3 mapbase 0x01c28800
[ 0.710000] sunxi-uart.2: ttyS1 at MMIO 0x1c28800 (irq = 3) is a U6_16550A
[ 0.720000] G2D: drv_g2d_init
[ 0.720000] G2D: g2dmem: g2d_start=49000000, g2d_size=1000000
[ 0.730000] G2D: head:c9000000,tail:ca000000
[ 0.730000] G2D: Module initialized.major:252
[ 0.740000] brd: module loaded
[ 0.740000] loop: module loaded
[ 0.750000] nand driver, init.
[ 0.750000] cmu_clk is 480
[ 0.750000] nand clk init end
[ 0.760000] offset 0xc:0x6141
[ 0.760000] offset 0x14:0x8200000b
[ 0.760000] nand gpio_request
[ 0.770000] nand driver version: 0x2 0x9
[ 0.770000] nand interrupte register ok
[ 0.780000] ret of NFC_ChangMode is 0
[ 0.780000] dma_hdleis 0
[ 0.780000] dma_hdleis 10000008
[ 0.790000] cmu_clk is 480
[ 0.790000] nand clk init end
[ 0.790000] offset 0xc:0x6141
[ 0.800000] offset 0x14:0x82000007
[ 0.860000] Dev nand: part 1, start 2048, size 131072
[ 0.860000] Dev nand: part 2, start 133120, size 4096
[ 0.870000] Dev nand: part 3, start 137216, size 2097152
[ 0.870000] Dev nand: part 4, start 2234368, size 2097152
[ 0.880000] Dev nand: part 5, start 4331520, size 2097152
[ 0.880000] Dev nand: part 6, start 6428672, size 1048576
[ 0.890000] Dev nand: part 7, start 7477248, size 501760
[ 0.890000]nand: nanda nandb nandc nandd nande nandf nandg
[ 0.900000] benn: nand probe enter
[ 0.910000] nand driver, ok.
[ 0.910000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.920000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.920000] : open clock
[ 0.950000] : Set USB Power ON
[ 0.950000] sw-ehci sw-ehci.1: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.960000] sw-ehci sw-ehci.1: new USB bus registered, assigned bus number 2
[ 0.960000] sw-ehci sw-ehci.1: irq 39, io mem 0xf1c14000
[ 0.990000] sw-ehci sw-ehci.1: USB 0.0 started, EHCI 1.00
[ 0.990000] hub 2-0:1.0: USB hub found
[ 1.000000] hub 2-0:1.0: 1 port detected
[ 1.000000] : open clock
[ 1.020000] sw-ohci sw-ohci.1: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.030000] sw-ohci sw-ohci.1: new USB bus registered, assigned bus number 3
[ 1.040000] sw-ohci sw-ohci.1: irq 64, io mem 0xf1c14400
[ 1.100000] hub 3-0:1.0: USB hub found
[ 1.100000] hub 3-0:1.0: 1 port detected
[ 1.110000] : open clock
[ 1.130000] : Set USB Power ON
[ 1.140000] sw-ehci sw-ehci.2: SW USB2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.140000] sw-ehci sw-ehci.2: new USB bus registered, assigned bus number 4
[ 1.150000] sw-ehci sw-ehci.2: irq 40, io mem 0xf1c1c000
[ 1.180000] sw-ehci sw-ehci.2: USB 0.0 started, EHCI 1.00
[ 1.180000] hub 4-0:1.0: USB hub found
[ 1.190000] hub 4-0:1.0: 1 port detected
[ 1.190000] : open clock
[ 1.210000] sw-ohci sw-ohci.2: SW USB2.0 'Open' Host Controller (OHCI) Driver
[ 1.220000] sw-ohci sw-ohci.2: new USB bus registered, assigned bus number 5
[ 1.230000] sw-ohci sw-ohci.2: irq 65, io mem 0xf1c1c400
[ 1.290000] hub 5-0:1.0: USB hub found
[ 1.290000] hub 5-0:1.0: 1 port detected
[ 1.300000] mousedev: PS/2 mouse device common for all mice
[ 1.300000] sunxi RTC version 0.1
[ 1.310000] sunxi-rtc sunxi-rtc: sunxi_rtc_probe tmp_data = 380248073
[ 1.310000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 1.320000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
[ 1.330000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 1.330000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
[ 1.340000] sunxi-rtc sunxi-rtc: rtc core: registered rtc as rtc0
[ 1.340000] i2c /dev entries driver
[ 1.350000] lirc_dev: IR Remote Control driver registered, major 251
[ 1.350000] IR NEC protocol handler initialized
[ 1.360000] IR RC5(x) protocol handler initialized
[ 1.360000] IR RC6 protocol handler initialized
[ 1.370000] IR JVC protocol handler initialized
[ 1.370000] IR Sony protocol handler initialized
[ 1.380000] IR RC5 (streamzap) protocol handler initialized
[ 1.380000] IR SANYO protocol handler initialized
[ 1.390000] IR MCE Keyboard/mouse protocol handler initialized
[ 1.390000] IR LIRC bridge handler initialized
[ 1.400000] : install start!!!
[ 1.400000] : install end!!!
[ 1.400000] start!!!
[ 1.410000] init end!!!
[ 1.410000] start!!!
[ 1.410000] init end!!!
[ 1.420000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 1.430000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 1.430000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 1.440000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
[ 1.450000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
[ 1.460000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 1.470000] Bluetooth: HCI UART driver ver 2.2
[ 1.470000] Bluetooth: HCI H4 protocol initialized
[ 1.480000] Bluetooth: HCI BCSP protocol initialized
[ 1.480000] Bluetooth: HCILL protocol initialized
[ 1.480000] cpuidle: using governor ladder
[ 1.490000] cpuidle: using governor menu
[ 1.490000] : no sdio card used in configuration
[ 1.500000] : sunximmc_init
[ 1.500000] : sunxi mmc controller using config : 0xb
[ 1.510000] : sunxi-mmc.0: pdev->name: sunxi-mmc, pdev->id: 0
[ 1.510000] : mmc 0 power off !!
[ 1.520000] : mmc0 Probe: base:0xf1c0f000 irq:32 dma:0 pdes:0xef394000, ret 0.
[ 1.530000] : sunxi-mmc.1: pdev->name: sunxi-mmc, pdev->id: 1
[ 1.530000] : mmc 1 power off !!
[ 1.540000] : mmc1 Probe: base:0xf1c10000 irq:33 dma:0 pdes:0xef398000, ret 0.
[ 1.550000] : sunxi-mmc.3: pdev->name: sunxi-mmc, pdev->id: 3
[ 1.550000] : mmc 3 power off !!
[ 1.560000] : mmc3 Probe: base:0xf1c12000 irq:35 dma:0 pdes:0xef39c000, ret 0.
[ 1.570000] IPv4 over IPv4 tunneling driver
[ 1.570000] TCP: cubic registered
[ 1.570000] Initializing XFRM netlink socket
[ 1.580000] NET: Registered protocol family 10
[ 1.590000] IPv6 over IPv4 tunneling driver
[ 1.590000] NET: Registered protocol family 17
[ 1.600000] NET: Registered protocol family 15
[ 1.600000] Bluetooth: RFCOMM TTY layer initialized
[ 1.610000] Bluetooth: RFCOMM socket layer initialized
[ 1.610000] Bluetooth: RFCOMM ver 1.11
[ 1.620000] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.620000] Bluetooth: BNEP filters: protocol multicast
[ 1.630000] 8021q: 802.1Q VLAN Support v1.8
[ 1.630000] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 1.640000] Registering SWP/SWPB emulation handler
[ 1.640000] registered taskstats version 1
[ 1.650000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 1.660000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
[ 1.660000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
[ 1.670000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 1.680000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 1.690000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 1.690000] sunxi-rtc sunxi-rtc: sunxi_rtc_gettime
[ 1.700000] sunxi-rtc sunxi-rtc: read time 2010-1-1 0:4:16
[ 1.710000] sunxi-rtc sunxi-rtc: setting system clock to 2010-01-01 00:04:16 UTC (1262304256)
[ 1.710000] ALSA device list:
[ 1.720000] No soundcards found.
[ 1.720000] Waiting for root device /dev/mmcblk0p2...
[ 2.520000] : mmc 0 detect change, present 1
[ 2.820000] : mmc 0 power on !!
[ 2.860000] : sdxc_request_done(L1114): smc 0 err, cmd 52,RTO !!
[ 2.860000] : sdxc_request_done(L1114): smc 0 err, cmd 52,RTO !!
[ 2.870000] : sdxc_request_done(L1114): smc 0 err, cmd 8,RTO !!
[ 2.880000] : sdxc_request_done(L1114): smc 0 err, cmd 5,RTO !!
[ 2.890000] : sdxc_request_done(L1114): smc 0 err, cmd 5,RTO !!
[ 2.900000] : sdxc_request_done(L1114): smc 0 err, cmd 5,RTO !!
[ 2.900000] : sdxc_request_done(L1114): smc 0 err, cmd 5,RTO !!
[ 2.920000] : sdxc_request_done(L1114): smc 0 err, cmd 8,RTO !!
[ 2.940000] mmc0: new high speed SD card at address 0260
[ 2.950000] mmcblk0: mmc0:0260 NCard 481 MiB
[ 2.960000]mmcblk0: p1 p2
[ 2.960000] platform reg-20-cs-ldo2: Driver reg-20-cs-ldo2 requests probe deferral
[ 2.970000] platform reg-20-cs-ldo3: Driver reg-20-cs-ldo3 requests probe deferral
[ 2.980000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 2.980000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
[ 2.990000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
[ 3.000000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 3.050000] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 3.060000] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
[ 3.080000] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.090000] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 3.100000] devtmpfs: mounted
[ 3.100000] Freeing init memory: 168K
probing /dev/mmcblk0 for uboot env data
Detected generic sunxi // generic sunxi
- preinit -
Press the key and hit to enter failsafe mode
- regular preinit -
[ 9.270000] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
- init -
Please press Enter to activate this console. [ 10.500000] !!! base_Addr = 0xf1c2ac00
[ 10.510000] config i2c gpio with gpio_config api
[ 10.510000] twi0, apb clock = 24000000
[ 10.530000] axp_mfd 0-0034: AXP (CHIP ID: 0x41) detected
[ 10.550000] axp20_ldo1: 1300 mV
[ 10.570000] axp20_ldo2: 1800 <--> 3300 mV at 3000 mV
[ 10.600000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 10.600000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
[ 10.620000] axp20_ldo3: 700 <--> 3500 mV at 2800 mV
[ 10.640000] platform reg-20-cs-buck2: Driver reg-20-cs-buck2 requests probe deferral
[ 10.640000] platform reg-20-cs-ldo4: Driver reg-20-cs-ldo4 requests probe deferral
[ 10.680000] axp20_ldo4: 1250 <--> 3300 mV at 2800 mV
[ 10.740000] axp20_ldo2: Failed to create debugfs directory
[ 10.740000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 10.820000] axp20_buck2: 700 <--> 2275 mV at 1400 mV
[ 10.820000] platform reg-20-cs-buck3: Driver reg-20-cs-buck3 requests probe deferral
[ 10.900000] axp20_buck3: 700 <--> 3500 mV at 1250 mV
[ 10.970000] platform reg-20-cs-ldoio0: Driver reg-20-cs-ldoio0 requests probe deferral
[ 10.990000] axp20_ldoio0: 1800 <--> 3300 mV at 2800 mV
[ 11.080000] input: axp20-supplyer as /devices/platform/sunxi-i2c.0/i2c-0/0-0034/axp20-supplyer.41/input/input0
[ 11.380000] I2C: i2c-0: AW16XX I2C adapter
[ 11.490000] !!! base_Addr = 0xf1c2b000
[ 11.490000] twi1, apb clock = 24000000
[ 11.580000] I2C: i2c-1: AW16XX I2C adapter
[ 11.650000] !!! base_Addr = 0xf1c2b400
[ 11.650000] twi2, apb clock = 24000000
[ 11.760000] I2C: i2c-2: AW16XX I2C adapter
[ 11.930000] enter sun4i Audio codec!!!
[ 11.930000] sun4i audio support initialized
[ 11.940000] sun4i Audio codec successfully loaded..
[ 11.960000] input: sun4i-ir as /devices/virtual/input/input1
[ 11.960000] IR Initial OK
[ 11.970000] wemac Ethernet Driver, V1.01 in file:drivers/net/ethernet/sun4i/sun4i_wemac.c
[ 11.980000] ahb clk enable
[ 11.980000] ahb gate clk: 0x2615f
[ 12.030000] emac MAC isn't valid!
[ 12.040000] sw_ahci sw_ahci.0: controller can't do PMP, turning off CAP_PMP
[ 12.050000] sw_ahci sw_ahci.0: forcing PORTS_IMPL to 0x1
[ 12.060000] sw_ahci sw_ahci.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[ 12.070000] sw_ahci sw_ahci.0: flags: ncq sntf pm led clo only pio slum part ccc
[ 12.070000] scsi0 : sw_ahci_platform
[ 12.080000] ata1: SATA max UDMA/133 mmio port 0x100 irq 56
[ 12.440000] ata1: SATA link down (SStatus 0 SControl 300)
[ 12.480000] PPP generic driver version 2.4.2
[ 12.500000] tun: Universal TUN/TAP device driver, 1.6
[ 12.500000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 12.540000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 12.600000] xt_time: kernel timezone is -0000
[ 12.630000] nf_conntrack version 0.5.0 (14595 buckets, 58380 max)
[ 12.730000] usbcore: registered new interface driver cdc_acm
[ 12.740000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 12.760000] usbcore: registered new interface driver usbserial
[ 12.770000] usbcore: registered new interface driver usbserial_generic
[ 12.780000] USB Serial support registered for generic
[ 12.780000] usbserial: USB Serial Driver core
[ 12.800000] Initializing USB Mass Storage driver...
[ 12.810000] usbcore: registered new interface driver usb-storage
[ 12.810000] USB Mass Storage support registered.
[ 12.820000] usbcore: registered new interface driver cdc_ncm
[ 12.850000] usbcore: registered new interface driver option
[ 12.860000] USB Serial support registered for GSM modem (1-port)
[ 12.900000] usbcore: registered new interface driver uvcvideo
[ 12.900000] USB Video Class driver (1.1.1)
[ 16.030000] wemac wemac.0: WARNING: no IRQ resource flags set.
[ 16.140000] wemac wemac.0: eth0: link down
[ 16.140000] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 16.210000] device eth0 entered promiscuous mode
[ 16.210000] ADDRCONF(NETDEV_UP): br-lan: link is not ready
BusyBox v1.19.4 (2013-05-25 19:11:40 CEST) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.||||.----.||_
| - ||_|-__| |||||| _|| _|
|_______|| __|_____|__|__||________||__||____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
BARRIER BREAKER (Bleeding Edge, r36713)
-----------------------------------------------------
* 1/2 oz Galliano Pour all ingredients into
* 4 oz cold Coffee an irish coffee mug filled
* 1 1/2 oz Dark Rum with crushed ice. Stir.
* 2 tsp. Creme de Cacao
-----------------------------------------------------
root@OpenWrt:/#
Busybox：root@OpenWrt:/# busybox
BusyBox v1.19.4 (2013-05-25 19:11:40 CEST) multi-call binary.
Copyright (C) 1998-2011 Erik Andersen, Rob Landley, Denys Vlasenko
and others. Licensed under GPLv2.
See source distribution for full notice.
Usage: busybox ...
or: busybox --list[-full]
or: function ...
BusyBox is a multi-call binary that combines many common Unix
utilities into a single executable.Most people will create a
link to busybox for each function they wish to use and BusyBox
will act like whatever it was invoked as.
Currently defined functions:
[, [[, arping, ash, awk, basename, brctl, bunzip2, bzcat, cat, chgrp,
chmod, chown, chroot, clear, cmp, cp, crond, crontab, cut, date, dd,
df, dirname, dmesg, du, echo, egrep, env, expr, false, fgrep, find,
free, fsync, grep, gunzip, gzip, halt, head, hexdump, hostid, hwclock,
id, ifconfig, init, insmod, kill, killall, klogd, less, ln, lock,
logger, logread, ls, lsmod, md5sum, mkdir, mkfifo, mknod, mkswap,
mktemp, mount, mv, nc, netmsg, netstat, nice, nslookup, ntpd, passwd,
pgrep, pidof, ping, ping6, pivot_root, poweroff, printf, ps, pwd,
readlink, reboot, reset, rm, rmdir, rmmod, route, sed, seq, sh, sleep,
sort, start-stop-daemon, strings, swapoff, swapon, switch_root, sync,
sysctl, syslogd, tail, tar, tee, telnet, telnetd, test, time, top,
touch, tr, traceroute, true, udhcpc, umount, uname, uniq, uptime,
vconfig, vi, watchdog, wc, wget, which, xargs, yes, zcat
root@OpenWrt:/#
这样弄OPENWRT在SD卡上启动比较繁琐 请问安装了OpenWRT在CB上，如何添加自己需要的东西呢？比如我想加一个可以实现文件转换的小程序，除了写这个程序之外，还需要怎样添加到OpenWRT上呢？ komoner0 发表于 2013-9-5 15:10 static/image/common/back.gif
请问安装了OpenWRT在CB上，如何添加自己需要的东西呢？比如我想加一个可以实现文件转换的小程序，除了写这 ...
ow里面有opkg命令能安装东西，但是sunxi目前不可用因为官网没这玩意。外部添加程序请用scp 可否支持CB3？ 好东西，先谢谢了，cb2，买卡准备刷:lol zpd1047 发表于 2013-12-21 14:51 static/image/common/back.gif
好东西，先谢谢了，cb2，买卡准备刷
cb2有内核问题，还是要编译 最近正想搞这个，谢谢楼主 下载包的速度很慢啊，动不动就中断了。版主能不能放一个编译好的镜像出来？ zpd1047 发表于 2013-12-21 14:51 static/image/common/back.gif
好东西，先谢谢了，cb2，买卡准备刷
cb2怎么编译这玩意，装GCC失败
页:
[1]