论坛 › Cubieez › Cubieez为cb2出个新版本吧

zixi0007 发表于 2014-11-21 09:17:06

Cubieez为cb2出个新版本吧

如题，都没有合适的linux用了。

facat 发表于 2014-11-21 09:31:37

怎么样叫合适？

sunbeyond 发表于 2014-11-21 09:34:32

已经有了，cb2的cubieez：http://pan.baidu.com/s/1hquyzB2#path=%252FModel%252Fcubieboard2%252FImage%252FLinux-distribution%252FCubieez

aaron 发表于 2014-11-21 09:35:53

这里有最新的debian-server和cubieez
http://pan.baidu.com/s/1sjv2lkD

zixi0007 发表于 2014-11-21 10:34:10

aaron 发表于 2014-11-21 09:35
这里有最新的debian-server和cubieez
http://pan.baidu.com/s/1sjv2lkD

有内存版吗？只有卡刷的镜像啊

aaron 发表于 2014-11-21 11:16:51

zixi0007 发表于 2014-11-21 10:34 static/image/common/back.gif
有内存版吗？只有卡刷的镜像啊

大家还是对nand有特殊情感啊，这个有还没上传

zixi0007 发表于 2014-11-22 07:10:39

aaron 发表于 2014-11-21 11:16
大家还是对nand有特殊情感啊，这个有还没上传

对！nand版稳定点

gcd0318 发表于 2014-11-25 17:43:45

我在cb2上用archlinux
http://archlinuxarm.org/platforms/armv7/allwinner/cubieboard-2
cb1也有一版
http://archlinuxarm.org/platforms/armv7/allwinner/cubieboard
可惜ct没有，我才无奈用了cubian

aaron 发表于 2014-11-25 17:55:21

gcd0318 发表于 2014-11-25 17:43 static/image/common/back.gif
我在cb2上用archlinux
http://archlinuxarm.org/platforms/armv7/allwinner/cubieboard-2
cb1也有一版


这里有个版本，有些旧
http://dl.cubieboard.org/software/a20-cubietruck/archlinux/ct-arch-v2/
为何如此狂热？

zixi0007 发表于 2014-11-27 13:57:34

gcd0318 发表于 2014-11-25 17:43 static/image/common/back.gif
我在cb2上用archlinux
http://archlinuxarm.org/platforms/armv7/allwinner/cubieboard-2
cb1也有一版


这个cb2也只能卡刷是吧。

Replace sdX in the following instructions with the device name for the SD card as it appears on your computer.
1.Start fdisk to partition the SD card:
fdisk /dev/sdX
2.At the fdisk prompt, delete old partitions and create a new one:
a.Type o. This will clear out any partitions on the drive.
b.Type p to list partitions. There should be no partitions left.
c.Now type n, then p for primary, 1 for the first partition on the drive, 2048 for the first sector, and then press ENTER to accept the default last sector.
d.Write the partition table and exit by typing w.

3.Create and mount the ext4 filesystem:
mkfs.ext4 /dev/sdX1
mkdir mnt
mount /dev/sdX1 mnt
4.Download and extract the root filesystem:
wget http://archlinuxarm.org/os/ArchLinuxARM-sun7i-latest.tar.gz
bsdtar -xpf ArchLinuxARM-sun7i-latest.tar.gz -C mnt
sync
5.Install the U-Boot bootloader:
dd if=mnt/boot/u-boot-sunxi-with-spl.bin of=/dev/sdX bs=1024 seek=8
umount mnt
sync
6.Insert the micro SD card into the Cubieboard 2, connect ethernet, and apply 5V power.
7.Use the serial console or SSH to the IP address given to the board by your router. The default root password is 'root'.

查看完整版本: Cubieez为cb2出个新版本吧